How to operate the upper thread?
1. Wire on the spinning wheel. Open the stop coil on the fishing boat, put the fishing line on the fishing boat with the left hand, and wind the right hand clockwise along the axle slot for 5 to 6 turns. If you wind it several times, the effect will be better. The purpose of this method is to make the fishing line tightly lock the axle.
2. Fix the thread head. Turn the thread end of the left hand around the main line held by the right hand for 3 or 4 circles, tie a bridle knot to tighten the thread end, cut the thread end with scissors, and the fishing line is firmly fixed on the wheel axle.
3. Go online. Pull back the stop coil on the fishing wheel, turn the fishing line back clockwise, roll the fishing line into the fishing wheel with even force, and finally press the thread head on the metal wire pole
How to install the reel in fishing knowledge?
Illustration of the first type of fishing line
First fold the fishing line in half as shown in the figure
Bend the folded fishing line head back to form a coil as shown in the figure.
The bent thread ends are threaded into the coil formed just now as shown in the figure, which is equivalent to entanglement of the two thread bodies folded in half for the first time. Repeat the previous step for 3-4 turns.
After winding, pull both ends of the knot with both hands and tighten the thread head as shown in the figure.
After tightening the thread ends, cut the remaining thread with scissors. At this time, we have tied a looper coil, and the wire knot of the looper part is also very firm.
After opening the wire cup holder of the spinning wheel, put the looper we just tied on the wire cup. As shown in the figure.
As shown in the figure, tighten the fishing line so that the looper is tight on the thread cup of the spinning wheel.
How to use the threading wheel?
Four main use methods of spinning wheel
Spinning wheel, also known as spinning winding wheel, is the most widely used winding wheel at present. It is mainly composed of a winding shaft (wire cup), a wave rack (wire gear), a rocker arm, a force relief device, and a reverse knob (check switch). The advantages of spinning wheel are: low difficulty in throwing, suitable for throwing light bait and long-distance casting, simple structure, convenient disassembly and maintenance, and the most important thing is low price. The larger the volume of spinning wheel, the larger its fishing distance, the smaller its volume, and the smaller its fishing force. All kinds of winding wheels have performance indicators such as pulling force and occurrence of fishing lines with different diameters. Different fishing lines can be selected according to specific conditions. The use method of spinning wheel is as follows.
1. Go online. When the novice is online, it is better to operate together with two people, one holding the reel, the other holding the winding wheel, turn up the wave rack, then tie the thread end of the fishing line to the cup, finally put down the wave rack, shake the handle, and then you can wind the line on the cup. It is worth noting that no matter what diameter of thread is loaded, it should be slightly lower than the mouth of the cup, so it is not easy to mess up the thread.
2. Mount the pole. Install the winding wheel with fishing line on the fishing rod, open or unscrew the fishing rod wheel seat, insert the wheel foot into the wheel seat, and then close or tighten the wheel seat, so that the rod is installed. It is worth noting that the winding wheel must be firmly fixed on the fishing rod, otherwise it is easy to throw the wheel out when throwing the line forcefully. After installing the wheel, you can try to gently shake the winding wheel up and down, left and right with your hand. The purpose of this is to see whether the winding wheel is firm. If it is not firm, also check the cause. You can tighten and clamp the bayonet of the fishing rod wheel seat, and then reinstall the winding wheel.
3. Adjusting the pressure relief knob is also an important part. The so-called force relief knob is a device for adjusting the force on the winding wheel. In order to prevent the damage of the winding wheel caused by excessive external tension or the breaking of the rod, when the winding wheel is under a certain tension, it will automatically put some fishing lines out to relieve the tension of the confrontation between the two ends of the fishing line, and at the same time, it can better assist the fisherman to lift the fish. The adjustment of releasing force is generally based on the fishing force of the fishing line. If the pulling force of the fishing line is 3 kg, then a weight of * * * kg can be hung on the end of the line. At this time, the fishing rod and the fishing line are perpendicular to each other. Under this weight, the winding wheel can automatically set off the line, that is, it has been adjusted. The spring scale can also be used to adjust the release force. This method is more convenient. Remember that before the winding wheel with wire is put on the pole, directly bind the hook of the spring scale to the line. When the spring scale is pulled, when the scale of the spring scale shows * * * kg, the winding wheel will automatically set off, which should be adjusted.
4. Throw line. After finishing the preparation before casting, it is necessary to set out a reserved line about 30 cm long. Then turn the wave rack up, buckle the line on the index finger, press the line with your fingers, raise your hands over your head, and let the rod handle point to the target (reference object), so that the bait ball and fishing group are placed behind the manual forehead. When throwing, the left hand should press down properly. When the right hand releases the finger of pressing the line, it can push the rod forward. When the hook and bait fly out, the throwing rod and the tip of the rod should be aimed at the target. When the hook, bait and lead fall completely into the fishing point, you can pause for a moment, and then reset the line stop by hand to tighten the excess line, and tighten and fix the fishing line. At this time, it is necessary to check the lower check switch of the binding method of a fishing line. If the switch is not closed, it should be closed in time to avoid running when lifting the pole.
How can the fully closed fishing wheel go online?
After putting two loops of looper on the cup, it is OK to roll the thread directly, even if the thread is put at the end, it will not run away. It is better to fasten the thread end of the 8 sub-rings on the clip of the fishing line on the fishing boat when it is not used after the fishing boat retracts the line to prevent the fishing line from loosening. After the wire passes through the guide hole and reaches the cup mouth, open the iron ring, tie a dead set at the end of the wire with a diameter of about the same, and then pass the wire through the dead set for a short section to form a loop on the cup that opens the iron ring, and then buckle the iron ring to start winding. If it still doesn't fit, take it off and turn it over. There is one direction that must not follow. When winding the thread, use a person to hold it with a rag and eat a little harder, so that the thread will not be too loose.
How is the fishing line tied to the wheel?
Winding method:
1. Check the winding amount of the reel (generally marked on the reel or packing box), and select the appropriate fishing line model.
2. Install the fishing line wheel on the fishing rod and close the fishing line wheel check switch.
3. Knot one end of the line, pass through a guide ring of the fishing rod, open the outlet ring of the fishing boat, tie the line on the fishing boat, close the outlet ring, stretch the fishing line, check and ensure its fastening.
4. Keep the fishing line straight and tight, and start to rotate the fishing wheel rocker at a constant speed to entangle the line.
5. When the winding height is about * * * mm lower than the edge of the wire wheel, do not wind more or less, otherwise it will hinder you from casting the wire correctly. Keep the fishing line straight and tight, stop winding and cut the fishing line.
6. Then fix the fishing boat on the fishing boat seat on the fishing rod, and you can prepare for fishing. Although the drum fishing boat is not big, its line capacity is equal to that of the spinning fishing boat.